Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
bartgo schreef: ↑15 dec 2018, 21:46
Zou dat ook kunnen met een Rotex daikin hpsu, die modbus? Want dat klinkt wel als de oplossing ja.
Wat smartgrid betreft zou ik enkel het relaiscontact misbruiken om zelf het smartgrid signaal te simuleren zeg maar.
Ik dacht dat het relais contact enkel dient om de weerstanden spanningsvrij te schakelen door de netbeheerder, wanneer er stroom tekorten zijn? (alleszins zo in Duitsland)
Daarom is het concept van "hulp-weerstanden" in LW warmtepompen volgens mij achterhaald.
Mvg
Jeroen Beeckx
ZonLicht Bvba - Energie uit de Zon
SMA Advance Installer
SolarEdge Certified Installer
2520 Emblem http://www.zonlicht.net
Je hebt beide, Jeroen, bij tekort en te veel stroom. Maar overheid / netbeheerder geeft het signaal niet in belgie dus creëren we het signaal zelf he, toch dat voor overschot. Maar inderdaad enkel de weerstand terwijl ik die liever onbenut laat. Die staat al 2 jaar compleet uit.
Ik zou gewoon met de SHM enkel contacten willen aansturen, o.a. on/off van een zelfbouw warmtepompje (1000W elektrisch).
Zou bekabeld moeten werken, zonder Wifi. Iemand een idee?
Zolang enkel kan gestuurd worden via Wifi, blijft de SHM 2.0 op mijn bureau staan...
Mvg
Jeroen Beeckx
ZonLicht Bvba - Energie uit de Zon
SMA Advance Installer
SolarEdge Certified Installer
2520 Emblem http://www.zonlicht.net
@jeroen beeckx of @bartgo
Weten jullie of SHM V1 ook Ready SG protocol stuurt over de LAN ?
Mijn Nibe WP heeft een UTP uplink om te wekren met ready SG protocol, dus zou op die manier de WP kunnen sturen op een inteliggente manier SMA echter geeft geen gehoor aan mijn technische vragen
Anders moet ik mijn SHM V1 vervangen door een SHM V2 en zet ik mijn SHM V1 te koop.
PV1: 30 x ERA Black Solar 190WP, Kostal PIKO 5.5, O: 165° : H:30° |PV2: 16 x LG NeON2 Black 300WP, SMA3000TL-21, O: 255° : H:30° |PV3: 10 x LG NeON2 Black 300WP, SMASB1.5-1VL-40, O: 75 & 255° (polystring) : H:30° |WP: Nibe F1145-12 | ZB: Tisun FI 2/3 + Tisun FS 375/1R
Ik denk dat geen van beide zo een signaal geven. Je kunt beide wel programmeren met die Raspberry Pi zodat ze een relais contact in de WP gaan bedienen. Maar dat is dus zelf knutselen.
Connecting a load with an electronic control input (e.g., SG Ready or trigger input).
If you have a load with an electronic control input, the control input signals will be supplied by a relay with a floating
switching output (e.g., from Eltako). The load is hard-wired to the power supply and always has power. When 230 VAC
is applied to the relay through the radio-controlled socket, this activates the control input and starts the load.
5.3.1 ON/OFF Heat Pumps
An ON/OFF heat pump is a heat pump whose compressor runs with a constant speed during operation and draws a
constant level of power. In general, there are three options for controlling ON/OFF heat pumps:
• Control via radio-controlled sockets (230 V on/off) • Direct control via the SG-Ready input of the heat pump (normal / energy-intensive)
• Direct control via communication using data exchange protocol (SEMP)
Direct control via the SG-Ready input of the heat pump (normal / energy-intensive)
With this type of control, the heat pump is started even if the normal target temperature in the storage tank is reached.
A higher target temperature is temporarily activated via the SG-Ready input. This results in the heat pump being forced
to run in order to continue heating the water in the tank. The radio-controlled socket must be in "Switch-only mode". In
addition, a constant power consumption must be entered in the load profile of the heat pump in Sunny Portal.
Laatst gewijzigd door DaRkMaN_FX op 21 dec 2018, 20:44, 2 keer totaal gewijzigd.
PV1: 30 x ERA Black Solar 190WP, Kostal PIKO 5.5, O: 165° : H:30° |PV2: 16 x LG NeON2 Black 300WP, SMA3000TL-21, O: 255° : H:30° |PV3: 10 x LG NeON2 Black 300WP, SMASB1.5-1VL-40, O: 75 & 255° (polystring) : H:30° |WP: Nibe F1145-12 | ZB: Tisun FI 2/3 + Tisun FS 375/1R
Ja inderdaad. Dan maak je een relais die op 220v werkt en geeft die al dan niet stroom met een edimax of Bluetooth plug. Dat relais sluit of opent dan het smart grid signaal.
Probleem is dat bij daikin althans smart grid bij overschot zon betekent dat de el weerstand wordt aangezet en meer niet. Daar heb je niet zo veel aan, zeker niet in de zomer. En in de winter heb je geen overschot...
Voor mij haalt het ook niet uit om de WP te laten draaien in de zomer, als het vat opgewarmd kan worden met de ZB.
PV1: 30 x ERA Black Solar 190WP, Kostal PIKO 5.5, O: 165° : H:30° |PV2: 16 x LG NeON2 Black 300WP, SMA3000TL-21, O: 255° : H:30° |PV3: 10 x LG NeON2 Black 300WP, SMASB1.5-1VL-40, O: 75 & 255° (polystring) : H:30° |WP: Nibe F1145-12 | ZB: Tisun FI 2/3 + Tisun FS 375/1R